This wrench, in Dwayne Hanson's collection, came with an unfired 287 lantern
that was manufactured by the American Gas Machine Co.,
Albert Lea, Minnesota.
The wrench is 4 1/4" long and with nut openings of 7/16, 3/8, & 5/16".

American Gas Machine Co., Inc. supplied this 391-280 wrench
with their Model 3020 kerosene lantern.
Unlike the 3470 wrench below, this one was not fastened to the lantern.
It is 4 9/16" long with nut openings of 3/4, 5/8, 9/16, 1/2, 7/16,3/8, and 5/16"
and a tapered 5/16-5/32" slot for generator tips.
This wrench is in Fred Kuntz's collection.

American Gas Machine Co. Inc. attached wrenches
to the wing nut in the base of the globe cage of several lantern models.
This wrench was included with a Model 3470 lantern.
It is 2 9/16" in diameter
and fits nut sizes 5/8, 9/16, 1/2, 7/16, 3/8, & 5/16"
& includes a tapered 1/4-1/8" slot for generator tips.

This wrench came with Brien Page's Model 2534 three burner camp stove.
The wrench is 3 1/2" long and fits nut sizes 1/2 & 3/8" at the ends -
everything on the stove.
The center six-sided hole is for 5/16" nuts.

This 5" long wrench fits nut sizes 15/16, 7/16, 3/8, & 5/16" nuts.
As the 15/16" fuel cap is an unusually large size
that is only found on some AGM lamp and lantern models from the late 20's,
this may be wrench L49 that was sold with those models.
Note that the wrench is stamped LAMPS & LANTERNS.

This unusual paper with foil backing funnel
is meant to be folded as shown in the diagram in the center panel.
Jan Dyke believes the funnel was made in Canada
as it came with a 1950's Canadian Coleman 200
and the instructions are in English and French.
Jan would like more information on this funnel if you have it.

This wrench came with George Rocen's Model M Coleman lamp.
It is 4 7/8" long, and fits nut sizes 13/16, 9/16, 7/16 & 5/16"
plus it has a slot that is 5/32" wide for generator gas tips.

Coleman made this wrench for the CQ lamp model.
It is 4 7/8" long and fits nut sizes 13/16, 19/32, 7/16, and 11/32".
This wrench is in Neil McRae's collection.

Coleman made this LQ 66 wrench for their Quick-Lite lamp & lantern models
as well as for comparable models for Sunshine Safety.
The wrench is 4 7/8" long with 13/16, 9/16, 7/16" openings
and a 3/8" diameter hole for hanging.
This wrench is in Bob Willard's collection.

This wrench came with a Coleman L220 lantern dated Aug. 1928.
The instructions with the lantern identify this wrench
as part no. 362-950.
It is 4" long and fits nut sizes 11/16, 7/16, & 2, 5/16"
plus a 5/32" slotted generator tip remover.
This wrench also came with iron Models 4A & 609.

Coleman made this cleaning needle,
part number 104-905,
to clean gas tips on early generators
before built-in tip cleaners were designed.
There is a 0.006" wire at each end of this
1  5/16" long shaft.

Coleman made this Q44 wrench
to unscrew the generator tips for cleaning or replacement
on Quick-Lite models.
The wrench is 1  1/4" long with a 5/32" wide opening.

This is a Coleman "Universal Wrench,"
that was designed to be used on several appliances.
In this case it came with a Canadian Model 4A iron.
It is 4 7/8" long and has openings
that are 13/16, 11/16, 9/16, 1/2, 7/16, 3/8, & 5/16"
as well as a tapered opening 1/4-1/8."

Coleman made this combination handle-wrench
for the Model 530 "GI pocket stove."
The handle is 4 3/8" long x 1 2/5" high to hold the
pots into which the stove fits.
The wrench accepts 9/16 & 3/8" nuts.

This eccentric wrench made by Coleman, part no. 220-B-950,
nicely fits the globe base nut on 220/228 lantern models.
This 3 5/8" long wrench, in Neil McRae's collection,
is bent at the base to accept a 9/16" nut.

Coleman supplied cans for pouring preheating alcohol
into their kerosene fueled lanterns such as Model 237.
Most of these cans are of unpainted steel.
This can, in Don Colston's collection, is painted and with use directions on both sides.
The bend in the tube allows the user to fill the cup without removing the globe.

Coleman Canada made the No 0 filter funnel on the left and Coleman US made the one on the right.
These aluminum funnels have the blue felt filters
mounted in metal rings of aluminum (left) and copper (right).
The copper-aluminum combination will act as a battery when the felt retains moisture
so the filter corrodes into place. Most US funnels have aluminum rings.
The Canadian funnel has a fine brass screen (not seen) below the felt filter.

Coleman Part No 413-9401 is a check valve tool
in Bob Hitchcock's collection,
It appears in Coleman Parts Catalog 32A
which is dated Aug. 1955.

Another tool in Bob Hitchcock's collection
is this Coleman modified Utica brand pliers 1300-8.
Coleman ground off the end of the pliers so it could be used
to grip a burner tube for removal
without removing the air tube.

This Coleman wrench is part no. 605-950.
It is 4 1/8" long
and fits nut sizes 11/16, 9/16, 1/2, 7/16, 3/8, & 5/16"
and a slotted generator tip remover
that tapers to 5/32".

We believe that Coleman in Canada made this wrench
for their Model 200 lantern.
It is 4" long and has 11/16, 9/16, 1/2, 7/16, 3/8, and 5/16" openings
plus a 1/4-1/8" slotted opening,
presumably for generator tips.
This wrench is in Bob Willard's collection.

Continental-Licht und Apparatebau Gesellschaft m. b. H. Frankfurt am Main, Germany
made Transportable Lamp No. 66 circa 1910.
These two wrenches were supplied with the lamp,
which is in Erik Leger's collection.
The upper wrench is 154.5mm in length and has openings of 24, 13.45, and 8mm.
The lower wrench is 146mm long and has openings of 13 and 8mm.

These two wrenches came with a Continental-Licht Model 4615S
searchlight lantern in Erik Leger's collection.
The upper wrench is 115mm long and has 19.3 and 8mm openings.
The lower wrench is 130mm long and has 13 and 8 mm openings.

This wrench came with a Foote Mfg. Co., Dayton, Ohio, lamp in Dwayne Hanson's collection.
The wrench is 4 3/8" long and has 5/8" hex and square openings,
which are compatible with the nuts and bolts on the lamp.

Graetz Vertriebsgesellschaft mbH made this wrench
for their Petromax lanterns.
The wrench is 127mm in length and fits nut sizes 15, 10, & 9mm.
The tapered shank is a gauge to adjust the distance between the gas tip and the air tube
for the 350/500 cp lantern(left) and 250cp lantern (right).
The tip is a screwdriver to unscrew the center bolt
that holds the globe cage to the fount.

The Primus brand 1050 and 1080 series lanterns,
made by Aktiebolaget B.A. Hjorth, Sweden,
were supplied with this 96mm long wrench.
It fits nut sizes, 17.5, 9.5, 9.0, 4.0 and 1.5mm.
This wrench is in Neil McRae's collection.

Neil McRae made this wrench primarily to work on Primus type kerosene stoves
but it also is useful on a few Petromax style lanterns.
The end of the 16mm diameter shaft (right + close up) has a 5mm slot for the pump check valve
and the end of the 12mm diameter shaft (left) has a 4mm slot for the gas tips.
The manufactured tools for this purpose can easily damage these brass parts.
This wrench is 26 cm long; the 3/4" hex on the upper handle
doesn't work well for removing stove burners as it quickly hits the stove legs.

This 4" long wrench came with a Lind-O-Lite lantern model
with a wide ventilator and carburetor valve.
The wrench has openings of 11/16, 7/16, and 5/16"
with a slot got generator gas tip removal.
This wrench is in Henry Plews's collection.

The upper generator tip cleaner came with the Lind-O-Lite lantern as above
It is 2 1/4" long and the loop is 5/8" in diameter.
The loop is at right angles to the wire, perhaps causing the wire on one side to be missing.
The lower tip cleaner is of unknown manufacture.
It is 2 1/2" long and has a1/2" diameter loop.
These are in Henry Plews's collection.

This wrench was supplied with the M1950 military stoves
and fits between two of the stove's legs
when not in use.
It measures 3 1/4" long and has nut openings
that are 11/16, 7/16, and 11/32" plus a tapered slot for generator tips.
This wrench is in Neil McRae's collection.

Mil-spec lanterns were made by a number of manufacturers from 1944-1991
under contract to the U.S. Quartermaster Corps.
The wrench at the top is bent up at both ends so it will fit under a clip in the frame base.
It is 3 3/8" long and has 9/16" and 1/8" openings; a tip cleaner is held in place by a clip.
This wrench was supplied with lanterns up to the mid 1950's.
The wrench at the bottom was supplied with lanterns from the mid 1950's on;
it differs in being bent up only at one end and fits in the parts well in the fount.
These wrenches are in Dwayne Hanson's collection.

This key style wrench came with a Monitor iron
in Glenn Knapke's collection.
The wrench is nickel plated cast iron,
2 3/8" long and fits hex nut size 1/2" and square nut size 1/4."